TM
WIRELESS DEVICES
INSTALLATION GUIDE
Z
2
0
63
21-
0
B
PAGE 1 ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / suppor[email protected] 12121Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Aerospond, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
Network Wireless Gateway
SPECIFICATIONS
Input Power 20-30 VDC; 24 VAC ±20%, 50/60 Hz
Wireless Inputs 8 wireless analog sensor inputs; 8 wireless digital sensor inputs
Outputs:
Analog 8 outputs: 4-20 mA/0-5 VDC/0-10 VDC (selectable)
Digital 8 solid state contacts: 100 mA@30 VAC/DC
(N.O./N.C. configurable with Veris software)
Mimimum Load Impedence (Voltage Mode) 5000 Ω
Maximum Load Impedence (Current Mode) 500 Ω (absolute max.)
Operating Environment:
Operating Temperature Range 0° to 50°C (32° to 122°F)
Operating Humidity Range 0 to 95% RH noncondensing
Agency Approvals NEMA 1 housing; EN60950-1; ETL; CE
NWGWA2
DIMENSIONS
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classied locations.
• Read and understand the instructions before installing
this product.
• Turn off all power supplying equipment before working on it.
• The installer is responsible for conformance to all applicable codes.
No responsibility is assumed by Veris Industries for any consequences arising out of the
use of this material.
PRODUCT IDENTIFICATION
Part Number Description
NWGWA2 Network Wireless Gateway
Accessories (sold separately)
Part Number Description
AWB01 Wi-Fi conguration cable
AWB02 Antenna extension cable, 3 ft.
QUICK INSTALL
1. Congure all devices in the wireless network using the Veris conguration
software, available at www.veris.com.
2. Mount the NWGWA2 onto standard 35 mm DIN rail.
3. Install the antenna.
4. Wire the NWGWA2 to the power supply and the building control system’s input
card.
4.2”
(107mm)
3.6”
(91mm)
1.5”
(39mm)
2.3”
(59mm)
1.9”
(48mm)
1.8”
(45mm)
PRODUCT OVERVIEW
The Aerospond NWGWA2 network wireless gateway is designed to receive a wireless
(Wi-Fi) signal from the Veris Aerospond wireless sensors (the HWXW series humidity
sensors and the TWXWXX temperature sensor). These sensors monitor the interior
temperature and humidity conditions and convert the data into a wireless signal. The
NWGWA2 receives this signal and converts it to an analog 4-20 mA, 0-10 VDC, or 0-5
VDC output or to a digital contact closure output compatible with building control
systems.
FCC PART 15 INFORMATION
NOTE: This equipment has been tested by the manufacturer and found
to comply with the limits for a class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Modifications to this product without the express authorization of
Veris Industries nullify this statement.
IMPORTANT NOTE: To comply with FCC & IC RF exposure requirements, the antenna used
for this transmitter must be installed to provide a separation distance of at least 20cm
from all persons and must not be co-located or operate in conjunction with any other
antenna or transmitter.
EU
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels