Veris-industries H681x-5A SERIES Install Manuel d'utilisateur télécharger pdf

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

POWER MONITORING

INSTALLATION GUIDE

H6810, H6811,

H6812

Installer’s Speciﬁcations

Output at Rated Current 5 Amps AC

Accuracy see table (page 2)

Leads 18 AWG, UL 1015 twisted pair, 6’ (1.8 m) standard length

Operating Temperature Range -15° to 60°C (5° to 140°F)

Storage Temperature Range -40° to 70°C (-40° to 158°)

Humidity Range 0-95% noncondensing

Max. Voltage L-N Sensed Conductor 600 VAC (basic insulation rating)

Frequency Range 50/60 Hz

Altitude of Operation 3km max.

Installation Category Cat II or Cat III

5 Amp Split-Core Current Transformers

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ.

DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• SECONDARY LEADS/TERMINALS OF CURRENT OUTPUT (e.g. 5A) CTs MUST BE SHORTED,

OR CONNECTED TO THE BURDEN AT ALL TIMES.

Failure to follow these instructions will result in death or serious injury.

DANGER

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

PRODUCT IDENTIFICATION

INSTALLATION

1. Disconnect and lock out power to the primary circuit before installing these

current transducers (CTs).

2. Connect the secondary leads to the burden or test switching/shorting bar. The

white wire is the X1 lead.

3. Depress the tabs on one end of the current transformer to open it and slip it over

the primary leads. Note labeling on product indicating “source side.”

4. Check the core ends on both sections of the CT to assure there is no rust or debris in

the closure areas.

5. Close and latch the CT, and mount it securely.

6. Reconnect power to the panel.

Optional mounting kit available for the H6810, H6811, and H6812. See Veris AH06.

H681x-5A SERIES

H681

Model/Amps

Small:

0-200 = 200A

0-300 = 300A

Medium:

1-400 = 400A

1-600 = 600A

1-800 = 800A

Large:

2-800 = 800A

2-1000 = 1000A

2-1200 = 1200A

2-1600 = 1600A

2-2000 = 2000A

2-2400 = 2400A

Output Type

= 5 Amp

1 2

Résumé du contenu

Page 1 - H681x-5A SERIES

Page 2 - INSTALLATION GUIDE

Commentaires sur ces manuels

Pas de commentaire

Veris-industries H681x-5A SERIES Install Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Veris-industries H681x-5A SERIES Install. Veris Industries H681x-5A SERIES Install User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Veris-industries H681x-5A SERIES Install