Veris-industries H970HCA Install Manuel d'utilisateur télécharger pdf

CURRENT MONITORING

INSTALLATION GUIDE

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Split-Core Low Current 4-20mA & 0-5VDC

DC Current Transducer

Installer’s Speciﬁcations

Technology Open loop Hall eﬀect

Amperage Range 0 to 50/100/200 ADC (slide switch selectable)

Sensor Supply Voltage 15-30VAC/DC for 4-20mA output;

12-30VAC/DC for 0-5VDC output

Supply Current 35mA max.

Isolation 600VAC rms

Temperature Range -15° to 60°C (5° to 140°F)

Humidity Range 10-90% RH non-condensing

Output 4-20mA and/or 0-5VDC

Accuracy ±3% F.S. combined linearity, hysteresis, and repeatability

The product design provides for basic insulation only.

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ.

DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

DANGER

Wiring ExamplE

H970HCA

970HCA

DimEnsions

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

quick install

Disconnect and lock out power to the conductor to be monitored.1.

Choose a location for the sensor. The monitored conductor must pass through the 2.

iris, and the sensor must be at least ½” from any uninsulated conductors.

Install the adjustable mounting bracket to the back of the enclosure using the 3.

included screws.

Connect supply voltage wires to the terminals marked Power (+) and Gnd (-).4.

Wire the output (mA or VDC) connections between the sensor and the controller.5.

Snap the sensor over the conductor to be monitored and clip the assembly to the 6.

mounting bracket.

Set the ﬁeld-selectable switch to the desired amperage level (see page 2).7.

Fan or Pump

CONTROLLER

4-20mA DC

Analog

Input

MOTOR

CONTACTOR

Removable Mounting Bracket

Self-gripping

Iris

1.0”

(25 mm)

0.8”

(21 mm)

1.1”

(26 mm)

3.1”

(79 mm)

2.8”

(70 mm)

Ø = 0.3”

(8 mm)

1.4”

(36 mm)

2.5”

(64 mm)

3.0”

(76 mm)

Bracket can be mounted

on either side for added

installation ﬂexibility.

Use DIN Rail

Mounting clip

(Veris part

number AH01) to

mount on stan-

dard DIN rail.

1 2

DC Current Transducer 1
CAUTION 2

Résumé du contenu

Page 1 - DC Current Transducer

Page 2 - CAUTION

Commentaires sur ces manuels

Pas de commentaire

Veris-industries H970HCA Install Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Veris-industries H970HCA Install. Veris Industries H970HCA Install User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Veris-industries H970HCA Install