Veris-industries HWS SERIES Install Manuel d'utilisateur télécharger pdf

VERIS INDUSTRIES

™

environmental SenSorS

inStallation GUiDe

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Wall Mount with Analog Setpoints, LCD Display,

1% NIST, 2% NIST, 2%, 3%, or 5%

Installer’s Speciﬁcations

Power Supply* 15 to 24VDC/24VAC, 100mA max.

Outputs, Analog Switch Selectable 4-20mA or 0-10V/0-5VDC (switch aﬀects both outputs)

RH Sensor Digitally proﬁled thin-ﬁlm capacitive (32-bit mathematics)

U.S. Patent 5,844,138

Accuracy at 25°C from 10-80% RH** ±2%, 3%, or 5% models

±1% at 20-50% RH (Multi-point calibration NIST traceable)

Reset Rate*** 24 hours

Stability ±1% @ 20°C (68°F) annually, for two years

Linearity Included in Accuracy spec.

Operating Humidity Range 0-100% RH

Temperature Coeﬃcient ±0.1%RH/°C above or below 25°C (typical)

Operating Temperature Range 10° to 35°C (50° to 95°F)

Scaling 0-100% RH

Calibration Oﬀset Adjustable ±9.9% in 0.1% increments

Setpoint Range 10-80% RH in 1% increments

*One side of transformer secondary is connected to signal common, so an isolation transformer or

dedicated power supply may be required.

**Speciﬁed accuracy with 24VDC supplied power with rising humidity.

***Reset Rate is time required to recover to 50% RH after exposure to 90% RH for 24 hours.

To maintain CE compliance the connected power supply must have a CE mark supporting LV + CE

directives.

HWS SerieS HWS SerieS

Dimensions

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• Read and understand the instructions before installing

this product.

• Turn oﬀ all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

ProDuct iDentification

quick install

Select a mounting location away from ventilation sources. The sensor should be 1.

mounted on a vertical wall, about 4 ½ feet above the ﬂoor.

Aﬃx the backplate to the wall.2.

Wire the device. Refer to wiring diagram.3.

Install Cover. 4.

1.2"

(29 mm)

3.5"

(89 mm)

4.75"

(121 mm)

Enter

SetpointAccuracy NIST

= Analog

1 = 1%

2 = 2%

3 = 3%

5 = 5%

HWS

RH Only Device

N = NIST (1 & 2% only)

X = No (2, 3, 5% only)

1 2 3

Résumé du contenu

Page 1 - HWS SerieS HWS SerieS

Page 2 - HWS SerieS

Page 3

Commentaires sur ces manuels

Pas de commentaire

Veris-industries HWS SERIES Install Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Veris-industries HWS SERIES Install. Veris Industries HWS SERIES Install User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Veris-industries HWS SERIES Install