Veris-industries H735 Install Manuel d'utilisateur télécharger pdf

VERIS INDUSTRIES

™

CURRENT MONITORING

INSTALLATION GUIDE

Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.

Solid-Core Current Switch, Adjustable Output,

with Command Relay

Installer’s Speciﬁcations

Sensor Power Induced from monitored current

Insulation Class 600VAC rms (UL)

Frequency Range 50/60Hz

Relay Coil 24VAC/DC 10mA

Relay Contact 5A@250VAC/DC, 3A@30VDC, 1/6 hp

Temperature Range -15° to 60°C (5° to 140°F)

Humidity Range 10-90% RH non-condensing

Amperage Range 1-135A continuous

Output N.O. 0.1A@30VAC/DC, polarity insensitive

Hysteresis 10% of setpoint, typical

Oﬀ-State Leakage 1+ MΩ

Safety UL 508, CAT III

Do not use the LED status indicators as evidence of applied voltage.

The product design provides for basic insulation only.

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ.

DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

DANGER

Wiring ExamplE

H735

735

DimEnsions

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

quick install

Disconnect and lock out power.1.

Install the mounting bracket to the back of the electrical enclosure, no closer than 2.

1/2” (12mm) to an uninsulated conductor.

Slide the conductor to be monitored through the sensing hole of the current 3.

switch. Terminate the conductor. See Notes (page 2) for currents under 1 Amp or

above 135 Amps.

Wire the output connections to the DDC controller or switched load. Note: 4.

Contacts are solid state and work like dry contacts. When the switch is closed, less

than 1 Ω is present. When the switch is open, more than 1 MΩ are present.

Reconnect power.5.

Calibrate the sensor (see Calibration section).6.

0.2” x 0.15”

slot (2x)

1.1"

(27 mm)

2.8"

(68 mm)

0.7" Dia

(19 mm)

0.9"

(23 mm)

3.0"

(75 mm)

Removable/Adjustable Mounting Bracket

3.8"

(95 mm)

4.2"

(106 mm)

Fan or Pump

CONTROLLER

(Status)

(Relay

Coil)

Motor

CONTACTOR

CONTROL

POWER

1 2

INSTALLATION GUIDE 1
CAUTION 2

Résumé du contenu

Page 1 - INSTALLATION GUIDE

Page 2 - CAUTION

Commentaires sur ces manuels

Pas de commentaire

Veris-industries H735 Install Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Veris-industries H735 Install. Veris Industries H735 Install User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Veris-industries H735 Install